When a tankless water heater fails, the fault is usually one of a handful: mineral scale in the heat exchanger, a gas or power supply problem, a blocked vent or intake, a flow sensor or an ignition fault. The unit often shows a code. This page sits within the wider guide to water heater repair and focuses on the wall-hung kind found in Rancho Cucamonga and Upland homes.
Why has my tankless water heater stopped giving hot water?
Most often the unit is not firing, or it is firing and cannot keep up. Common reasons are scale blocking the heat exchanger, a closed gas valve or interrupted power, a clogged inlet filter, a blocked vent, or a flow rate too low to trigger the burner. An error code on the display narrows it down.
Run through the quick checks in order:
- Is the display lit? If not, check the outlet and breaker, since even gas units need power.
- Is the gas valve to the unit open, and do other gas appliances work?
- Is hot water missing everywhere or at one tap? One tap points to a faucet or cartridge issue.
- Do you see a code? The manual explains each code for that brand, and a photo helps the plumber.
- Try one tap at a normal flow. Tankless units can fail to fire at a trickle.
If the heater smells of gas, leave the building and call SoCalGas on 1-800-427-2200 from outside. Call 911 if you cannot reach them.
Does hard water damage a tankless heater here?
Yes, scale is the main enemy. The Department of Energy warns that hard water will damage a tankless unit, that scale can restrict flow through the heat exchanger and shorten the unit's life, and that tankless heaters should be flushed according to the manufacturer's instructions to prevent calcium buildup.
Local water is hard. The Cucamonga Valley Water District's 2025 report lists total hardness from 109 to 142 ppm, averaging about 125.5, which is about 7.3 grains per gallon by my calculation. The City of Upland's 2024 report shows an average of 163 ppm, about 9.6 grains. Other suppliers serve some streets, so check your bill and the supplier's report.
Scale shows up as lower flow, longer waits for hot water, a rumbling sound, temperature swings, and codes about overheating or flow. A flush uses a pump and descaling solution run through the unit, and the water softener options are covered in water softener installation.
When should a plumber repair a tankless heater?
Call a plumber for ignition faults, codes that return after a reset, gas smells, soot or yellow flame, venting problems, leaks from the unit, a flush that needs flow-control valves, or when the unit is more than a few years old and scaled. Gas appliances carry carbon monoxide and fire risks, so do not improvise.
We arrange for a local plumber to come out, diagnose the unit and quote in writing before work. A national price guide lists water heater repair at $150 to $750, which gives you a sense of scale. The written quote from a local plumber sets the real price. The Department of Energy says tankless units can last up to 20 years, so a repair on a well-maintained unit can be worth it. When a unit is failing repeatedly, compare replacing it with installing a new tankless heater or switching, as tank versus tankless explains.
If the water heater has failed with no hot water at all, see why there is no hot water, or ask for an urgent visit through the quote request.
How can I keep a tankless heater from failing again?
Flush it on the schedule in the manual, usually once a year in hard-water areas, keep the vent and air intake clear, replace the inlet filter screen when it clogs, and consider a softener or scale inhibitor upstream. Ask a plumber to record the settings and the flow rate at the visit.
Hard water is the cost of living in this region, and the Department of Energy specifically recommends evaluating the cold-water supply before installing a tankless unit. If scale builds up quickly, a whole-house softener or a scale-prevention cartridge is worth pricing. Keep the area around the unit clear and report any drips right away.
What can I check or fix myself?
Safe jobs are limited: reset the unit, check power and the gas valve, clean the cold water inlet filter after closing the water valves, and read the code. Anything involving the gas connection, the burner, the vent or the internal parts should wait for a plumber or the manufacturer's service.
The inlet screen filter catches grit and can clog. Shut off the water valves, open the filter housing slowly, rinse the screen and refit it. Do not take off panels on a gas unit that is plugged in and live unless the manual allows it. If you have a flush kit and the manual describes the steps, a flush is a reasonable annual job, but incorrect valves or a closed gas supply can damage the unit.
California requires a contractor license for jobs of $1,000 or more in labor and materials and any job that needs a permit. Gas appliance replacement usually involves a permit, as the page on gas line work explains.
How do I tell a flow problem from a failed part?
A flow problem shows up as hot water that works with a large tap opening but not a small one, or that fades when two taps run. A failed part usually triggers an error code, no ignition, or no hot water at any flow. A recently changed fixture, such as a low-flow showerhead, can also be the culprit.
Try three taps in turn: a sink, a shower, and a tub. If the unit fires at the tub but not the sink, flow is low rather than the burner failing. Many tankless units need a minimum flow to start. If hot water suddenly dies at all taps and the code mentions ignition or flame, a plumber should check the burner, igniter and gas supply.
A cold slug between two hot bursts is a separate matter. It often comes from small flows or from a long pipe run, and it is common in homes with a recirculation loop.
Common questions
How long does tankless hot water heater repair take?
A simple repair such as cleaning the inlet filter or replacing a sensor can take an hour or two. A flush takes longer, and a gas valve, heat exchanger or control board repair may need parts and a second visit. A replacement usually takes most of a day.
What should I ask before I hire someone for tankless hot water heater repair?
Ask for the contractor license number and look it up on the state board's site. Ask whether the price covers diagnosis, parts and a flush, whether a permit applies, what warranty the manufacturer gives on the part, and whether repair or replacement is the better choice for the unit's age.
Do I need to be home for tankless hot water heater repair?
Be there at the start to point out the unit and describe the fault, and to approve the written price. Water is shut off during the work, so plan for no hot water for a while. Someone adult should be home when gas is restored.
The rest of our guides start from plumber in Rancho Cucamonga.
Updated